Recall Notice from Smith & Wesson
- If your pistol is subject to this advisory, please call Smith & Wesson at 1-800-331-0852 or email us at MP380EZAdvisory@Smith-Wesson.com. A FedEx return label and shipping instructions to facilitate the return of your M&P 380 Shield EZ pistol will be mailed to you promptly. If you have any questions, you may call 1-800-331-0852 for more.
- In this case (or if you are unsure of your date of manufacture), simply go to MPShieldEZrecall.com and input your serial number, or call 888‐871‐7114. REMEDY/ACTION TO BE TAKEN: If your M&P Shield EZ Pistol is included in this recall, we will arrange for the return of your firearm to Smith & Wesson for inspection.
- Join Date Apr 2010 Location N/A, Pennsylvania Age 38 Posts 1,435 Rep Power 5048072.
https://www.mpshieldezrecall.com/
M&P SHIELD® EZ® PISTOL IMPORTANT SAFETY RECALL NOTICE FOR PISTOLS MANUFACTURED BETWEEN MARCH 1ST, 2020 AND OCTOBER 31ST, 2020
Smith & Wesson issued a pistol recall notice for their M&P Shield EZ pistols manufactured between the dates of March 1st – October 31st, 2020. Smith & Wesson has identified cracked hammers that fail to fully engage the sear which subsequently caused multiple successive discharges of the firearm without depressing the trigger. Jul 03, 2020 jonesy814. I have a 10-7 and a model 64-3. Both have a pinned barrel which was deleted some time in 1981. Both also were shipped in 1981 based on the serial numbers. The m64 has a 7D56xxx, and the m10 is 8D97xxx. If I recall correctly, they ran up into the 9D xxxxx range before switching to the 3 alpha prefix.
Smith And Wesson Shield Ez
Smith & Wesson has identified two M&P Shield EZ Pistols on which the hammers manufactured by our supplier were cracked. In those firearms, the hammer failed to fully engage the sear, causing the round to fire, cycling the slide, and potentially resulting in multiple discharges without depressing the trigger. This issue can occur in the following two scenarios:
With a loaded magazine in the firearm and the grip safety depressed, releasing the slide (by pulling it back, or releasing the slide stop), may ignite the round as the slide closes, without engaging the trigger. The condition may occur, regardless of the manual thumb safety position if equipped. This may also result in multiple discharges.
With a loaded magazine in the firearm, the grip safety depressed, manual safety in the fire position, slide closed, and a round in the chamber, pulling the trigger will cause the round to fire normally, however as the slide cycles, the next round may be ignited as it is chambered by the hammer failing to fully engage the sear, causing multiple discharges.
In all cases, the firearm will NOT fire unless the grip safety is depressed. While this condition has been found only in two hammers, and our investigation suggests that these two incidents are very isolated, any unintended discharge of a firearm has the potential to cause injury. Therefore, we have established this Safety Recall as a precautionary measure to ensure that all M&P Shield EZ Pistols in service meet our design specifications.
Stop using your M&P® Shield™ EZ pistol until you determine whether it is included in this safety recall, and if so, until it has been inspected and repaired by Smith & Wesson, if necessary.
Smith And Wesson Bodyguard Recall
PRODUCT AFFECTED:
Smith And Wesson Shield Recall Serial Numbers
This notice applies ONLY to M&P® Shield™ EZ pistols (including Performance Center® models) manufactured between March 1, 2020 and October 31, 2020, and only to a small percentage of that population. It does NOT apply to all SHIELD™ pistols. To determine whether your M&P Shield EZ Pistol is affected, check the label on the box to determine date of manufacture (see image below), and if manufacture date is between March 1, 2020 and October 31, 2020 – your pistol may be affected. In this case (or if you are unsure of your date of manufacture), simply go to MPShieldEZrecall.com and input your serial number, or call 888-871-7114 .